news

Recommended products

MORE

全部
  • 全部
  • 产品管理
  • 新闻资讯
  • 介绍内容
  • 企业网点
  • 常见问题
  • 企业视频
  • 企业图册

Performance introduction of horizontal light touch switch

Category:

Company News

Release time：2022-11-29

Views：

Outline： However, with the further improvement of living standards, this kind of household appliances will be upgraded faster and faster, and the total number of necessary appliances will become larger and larger, which is also the main development potential of its development prospects.

1. The manufacturer of horizontal light touch switch introduces in detail that if the load is increased on the terminal block when welding the terminal block, the possibility of looseness, deformation and deterioration of electrical characteristics will occur due to different standards. Please pay attention in the use process.

2. When using the buried hole printed circuit board and the circuit board not strongly recommended, because the influence of internal stress will change, please comprehensively determine the welding conditions in advance.

3. When carrying out 2 times of welding, please do it after some * * times of welding are restored to normal temperature. The continuous heating is likely to make the outfield part deformed, the end sister loose, fall off and reduce the electrical characteristics.

4. The specific mass production standard shall be determined for the precondition setting of welding.

5. The product is designed based on the principle of DC resistance load. Other loads [inductive load (L), capacitor load, please confirm. Supply of horizontal touch switch

6. For the screw hole and method of the printed circuit board, please refer to the recommended quantity and specification recorded in the product picture. Distributor of horizontal touch switch

7. This switch is used to press the structure of the switch directly through actual operation. Never use it for reflexive examination. Please select the cognitive switch of Qintai Electronics for the test function.

8. In the process of switch operation, if the required load is increased, the switch is likely to be damaged. Be sure not to increase the required force on the switch.

9. Please prevent the side from being used according to the operation part.

10. Analyzing the manufacturer of horizontal light touch switch, press the center of the switch as much as possible for the flat shaft rod type. For the hinge, please note that the pressing part of the rear axle rod will move. Due to its small size, multi gear, well proportioned driving force and good sense of section, it has been widely used in many industries such as electrical products.

However, with the further improvement of living standards, this kind of household appliances will be upgraded faster and faster, and the total number of necessary appliances will become larger and larger, which is also the main development potential of its development prospects.

key word:

previous

Structure and overview of touch switch

Which three points should be paid attention to when using the detection switch?

Next

Related news

Introduction to microswitch welding

Introduction to microswitch welding

The microswitch is welded one by one manually, which is characterized by the ability to accurately master the welding of each electronic device. The disadvantage is that it is too time-consuming and laborious.

Release time：2022-11-29 08:55

Application of touch switch

Application of touch switch

There are also many kinds of switches, among which the light touch switch is one of them. This switch plays a very important role in today's social life. Most people will be paralyzed without it in their daily life. So, it is convenient and fast to make everyone switch.

Release time：2022-11-29 08:55

[Detection switch] What should be paid attention to when selecting the detection switch for installation?

[Detection switch] What should be paid attention to when selecting the detection switch for installation?

Detection switch, a kind of position switch (also known as travel arrangement switch, positioning switch), is a common electrical product of low current cam controller. The production and processing kinetic energy components shall be used to impact the isolator to complete the connection or disconnection of the control circuit to ensure a certain control purpose. In general, this switch is used to limit the position or schedule of molecular thermal exercise, so that the industrial equipment for sports and fitness can automatically stop, repeatedly exercise, speed change exercise or automatic back and forth sports and fitness according to a certain position or schedule.

Release time：2022-11-29 08:55

Basic structure of connector

Basic structure of connector

To put it bluntly, the electronic device connector is to connect the circuit. In practical application, the four basic structures of the product are indispensable, that is, insulator, accessory, contact and shell. Now we will explain these mechanisms. We look forward to seeing the article, and you will have more understanding of the product.

Release time：2022-11-29 08:55